[1]赵瑨云,穆寄林,丁晓红,等.聚乳酸/醋酸纤维素蜂窝状复合多孔膜的形成与控制[J].高分子通报,2022,(10):131-137.[doi:10.14028/j.cnki.1003-3726.2022.10.014]
 ZHAO Jin-yun,MU Ji-lin,DING Xiao-hong,et al.Fabrication and Control of PLLA/CA Honeycomb Composite Porous Membrane[J].POLYMER BULLETIN,2022,(10):131-137.[doi:10.14028/j.cnki.1003-3726.2022.10.014]
点击复制

聚乳酸/醋酸纤维素蜂窝状复合多孔膜的形成与控制()
分享到:

《高分子通报》[ISSN:1003-3726/CN:11-2051/O6]

卷:
期数:
2022年10期
页码:
131-137
栏目:
出版日期:
2022-10-20

文章信息/Info

Title:
Fabrication and Control of PLLA/CA Honeycomb Composite Porous Membrane
作者:
赵瑨云 穆寄林 丁晓红 徐婕 胡家朋 林皓 付兴平
福建省生态产业绿色技术重点实验室, 武夷学院生态与资源工程学院, 武夷山 354300
Author(s):
ZHAO Jin-yun MU Ji-lin DING Xiao-hong XU Jie HU Jia-peng LIN Hao FU Xing-ping
Fujian Provincial Key laboratory of Eco-Industrial Green Technology, College of Ecological and Resources Engineering, Wuyi University, Wuyishan 354300, China
关键词:
水蒸气辅助法聚乳酸醋酸纤维素蜂窝孔亲水性
Keywords:
Breath figurePolylactideCellulose acetateHoneycombHydrophilicity
DOI:
10.14028/j.cnki.1003-3726.2022.10.014
文献标志码:
A
摘要:
以聚乳酸(PLLA)和醋酸纤维素(CA)为成膜材质,在一定温度和湿度条件下,利用水蒸气辅助法成功制备PLLA/CA蜂窝状复合多孔膜。研究溶剂种类、湿度、聚合物浓度、聚合物比例和成膜温度等条件对蜂窝孔形成的影响。实验结果表明环境湿度从43%增加至91%,蜂窝孔的孔径从1.67±1.34 μm增加至5.01±1.34 μm,且孔径大小与湿度呈现一阶线性关系。通过理论推导得到拟合直线的斜率为0.068,即环境湿度每增加1%,孔直径增加0.068 μm,孔直径的增长率为0.068 μm/%。聚合物浓度从1 wt%增加至6 wt%,蜂窝孔的孔径呈现先增大后减小的趋势。温度在10~50℃范围内,环境温度对孔形貌及其孔径并无太大影响。纯PLLA蜂窝状多孔膜的水接触角为(128.1±2.4)°,随着体系中CA含量增加,多孔膜的水接触角降低。当PLLA/CA=5:5时,水接触角为(50.2±1.4)°,说明体系中加入一定量CA后,多孔膜的亲水性提高,亲水性的提高有利于细胞在其表面的粘附、迁移、繁殖和生长。
Abstract:
PLLA/CA honeycomb composite porous membranes were prepared via Breath Figure method under certain humidity and temperature conditions with PLLA and CA as film materials. The effects of factors, such as solvent, relative humidity, polymer concentration, the ratio of polymer, and temperature, on the pore patterns and sizes were investigated. The results show that the pore size of PLLA/CA membranes increases from 1.67±1.34 μm to 5.01±1.34 μm with increasing relative humidity from 43% to 91%. The relationship of pore size and the relative humidity is presented first order liner relationship. Moreover, the slope of straight line is 0.068, which indicates that for every 1% in relative humidity, the pore size increases by 0.068 in this system. When the polymer concentration increases from 1 wt% to 6 wt%, the pore size of honeycomb increases first and then decreases. When the temperature is in the range of 10~50℃, the ambient temperature has no significant effect on the pore morphology and size. The water contact angle of pure PLLA honeycomb membrane is 128.1°±2.4°. With the increase of CA content, the water contact angle of porous membrane decreases. When PLLA/CA=5:5, the water contact angle was 50.2°±1.4°, indicating that a certain amount of CA was added into the system, the hydrophilicity of the porous membrane was improved, which was conducive to the adhesion, migration, reproduction and growth of cells on its surface.

参考文献/References:

[1] Gao X, Zhou J, Du R, Xie Z, Deng S, Liu R, Liu Z, Zhang J. Adv Mater, 2016, 28 (1):168~176.
[2] Han K, Heng L, Jiang L. ACS Nano, 2016, 10 (12):11087~11095.
[3] Izawa H, Kajimoto H, Morimoto M, Saimoto H, Ifuku S. RSC Adv, 2020, 10 (34):19730~19735.
[4] Zhou P, Shen Y, Zhao S, Li G, Yin Y, Lu R, Gao S, Han C, Wei D. J Alloys Compd, 2019, 789:129~138.
[5] Choi D C, Won Y J, Lee C H, Lee S, Lee M H, Khang D Y. J Mater Chem A, 2013, 1(40):12448~12454.
[6] Yin M J, Zhao Q, Wu J, Seefeldt K, Yuan J. ACS Nano, 2018, 12 (12):12551~12557.
[7] Liu Y, Deng J, Wang Y, Zhan X, Zhang D, Chen H. Coatings, 2020, 10 (11):112~119.
[8] Widawski, Gilles, Rawiso, Michel. Nature, 1994, 369 (6497):387~387.
[9] Srinivasarao M. Science, 2001, 292 (5514):79~83.
[10] Schatz M F, Neitzel G P. Annu Rev Fluid Mech, 2001, 33:93~127.
[11] Yeh S C, Wu C H, Huang Y C, Lee J Y, Jeng R J. Polymers, 2019, 11 (9):123~134.
[12] Yuan H, Li G, Dai E, Lu G, Huang X, Hao L, Tan Y. Chinese J Chem, 2020, 38 (12):1767~1779.
[13] 刘瑞来, 韩静, 陈秀娟, 雷声宏, 刘海清. 高分子学报, 2012,(3):291~298.
[14] 张幼珠, 吴佳林, 王立新, 尹桂波, 施德兵. 合成纤维工业, 2008,3:1~4.
[15] Hou J Z, Sun X P, Zhang W X, Li L L, Hong T. Chinese J Polym Sci, 2012, 30(6):916~922.
[16] Zhao B, Zhang J, Wang X, Li C. J Mater Chem, 2006, 16 (5):509~513.

相似文献/References:

[1]罗时荷,汪朝阳,杨丽庭,等.直接法共聚改性聚乳酸研究新进展[J].高分子通报,2011,(01):0.
[2]李菁,陈大凯,任杰,等.聚乳酸立构复合物的研究最新进展与应用展望[J].高分子通报,2011,(01):0.
[3]林海娟,方建勇,董丽松.聚乳酸阻燃性能的研究进展[J].高分子通报,2012,(03):45.
 LIN Hai-juan,FANG Jian-yong,DONG Li-song.Recent Progress in Flame Retardant of Polylactic Acid[J].POLYMER BULLETIN,2012,(10):45.
[4]兰婷,张俊娜,夏峰,等.聚乳酸纳米粒的改性研究进展[J].高分子通报,2012,(01):67.
 LAN Ting,ZHANG Jun-na,XIA Feng,et al.Research Progress on Modification of Poly(L-lactide) Nanoparticles[J].POLYMER BULLETIN,2012,(10):67.
[5]蒲文亮,唐颂超,张德震,等.不同分子量聚L-乳酸的非等温结晶动力学研究[J].高分子通报,2012,(06):76.
 PU Wen-liang,TANG Song-chao,ZHANG De-zhen,et al.Non-isothermal Crystallization Kinetics of Poly(L-lactic acid) in Different Molecular Weight[J].POLYMER BULLETIN,2012,(10):76.
[6]李永飞,吴勤,高美丽.外消旋丙交酯立体选择聚合研究进展[J].高分子通报,2012,(08):118.
 LI Yong-fei,WU Qin,GAO Mei-li.Recent Research Progress in Stereoselective Polymerization of Rac-lactide[J].POLYMER BULLETIN,2012,(10):118.
[7]武元鹏,丁强,李晶,等.基于聚乳酸的可降解形状记忆高分子的研究进展[J].高分子通报,2012,(10):33.
 WU Yuan-peng,DING Qiang,LI Jing,et al.Research Progress of Shape Memory Polymer Materials Based on Poly (Lactic Acid)[J].POLYMER BULLETIN,2012,(10):33.
[8]张海龙.聚乳酸在生物医药领域的改性研究进展[J].高分子通报,2012,(12):74.
 ZHANG Hai-long.Progress of Modification of Polylactide in Biomedicine Fields[J].POLYMER BULLETIN,2012,(10):74.
[9]吴涛,赵西坡,林真,等.完全降解聚乳酸共混复合材料的研究进展[J].高分子通报,2013,(02):84.
 WU Tao,ZHAO Xi-po,LIN zhen,et al.Research Progress in Completely Biodegradable Polylactide Blends[J].POLYMER BULLETIN,2013,(10):84.
[10]夏学莲,刘文涛,王利娜,等.生物医用PLA改性研究进展[J].高分子通报,2013,(11):29.
 XIA Xue-lian,LIU Wen-tao,WANG Li-na,et al.A Review of Biomedical Poly(lactic acid) Modification Research Progress[J].POLYMER BULLETIN,2013,(10):29.

备注/Memo

备注/Memo:
收稿日期:2021-6-15;改回日期:2021-8-6。
基金项目:国家自然科学基金(51406141),福建省自然科学基金(2020J01412、2020J01414),南平市基金(2019J06),南平市产业研究院(N2020Z012)
作者简介:赵瑨云(1983-),男,福建省人,副教授。E-mail:wyulrl@163.com
通讯作者:胡家朋,博士,教授。E-mail:wyuwqhjp@163.com.
更新日期/Last Update: 2022-09-20